Theben Tr 610 S User Manual
“THEBEN” Time Clock Setting Instructions continued…
Oct 21, 2016 THEBEN TR 612 S User's Guide French THEBEN TR 610 Top (TR610. If you are looking for the instruction manual: others THEBEN TR 612S - EIB - you have come to the right place. On this page you can download it for free. Page 1 of 2 Document #1200368.doc Rev 4 01/17/07. HAZARDOUS VOLTAGE: Risk of electric shock. Can cause injury or death. This device may be connected to more than one branch circuit. Disconnect all branch circuits WARNING STEFFES CORPORATION THEBEN. THEBEN TR 609 S User's Guide French BERNINA THEBEN TR 610 Top (TR610) User's Guide English THEBEN TR 653 S (TR653S) User's Guide English User's Guides, Owner's Manuals, Service Manuals, Instructions Books - The largest MOULINEX OW3101 CLEARVIEW 2608H THEBEN TR 610 S ISTRUZIONI. Theben TR 610 TOP2 Interruptor horario digital Caracter sticas del. The Theben company is presenting itself in 2005 for the first time as a system supplier in the fields of time, light and climate. Early manual over-ride switching for on and off without influencing. TR 651 S, TR 652 S, TR 653 S Termina®.
Page 2 of 2
Document #1200368.doc Rev 4
01/17/07
·
On
Off
·
On
4.
'HOUR' will be displayed across the top. Use the '◄' or '►' button to adjust the hour. Press 'OK'.
5.
'MINUTE' will be displayed across the top. Use the '◄' or '►' button to adjust the minutes. Press 'OK'.
6.
'MONDAY' will display. Select the days of the week that this particular program setting pertains to by using the '◄'
or '►' button until the first day of the cycle is flashing. Press 'OK' and 'COPY' will flash. Press 'OK' and 'ADD TU'
will appear. Continue to press 'OK' to select the desired days. To bypass a day, press '►'. After 'ADD SU' is
displayed and/or selected, 'STORE' flashes on the display. Press 'OK'. 'NEW PROG' will flash across the display.
7.
Press “OK” and '►' to set “TIME OFF” (control cycle). Repeat Steps 36 to program “TIME OFF” (control cycle).
8. Hans zimmer piano manual download.
Press “OK” to enter another program cycle or press “MENU” to return to the standard display.
C. VIEWING THE CHARGE (ON) AND CONTROL (OFF) CYCLES
1.
To view the program settings, press the 'Menu' until 'Prog' starts flashing. Press 'OK'. 'NEW PROG' will flash
across the top of the display. Press the '◄' or the '►' button until 'CHECK' flashes on the display.
2.
Continue to press and release 'OK' button to review the programs.
D. CLEARING A SINGLE CHARGE (ON)/CONTROL (OFF) CYCLE
1.
To clear individual program settings, press the 'Menu' until 'Prog' is flashing. Press 'OK'. 'NEW PROG' will flash
on the display. Press the '◄' or the '►' button until 'CLEAR' flashes on the display. Press 'OK'.
2.
'SINGLE' will flash on the display. Press 'OK' and use the '◄' or the '►' button until the day of the week desired is
displayed. Press 'OK'.
3.
Use the '◄' or the '►' button to select 'CLEAR' if clearing the current program setting. Press 'OK' and the current
program setting will be cleared.
NOTE: If the setting to be cleared is not displayed, use the '◄' or the '►' button until 'NEXT' is
displayed. Press 'OK'. The next program setting for the selected day will appear. Continue to
use the 'NEXT' button until the desired program setting is displayed.
E. CLEARING ALL CHARGE (ON) AND CONTROL (OFF) CYCLES
1.
To clear all existing program settings, press the 'Menu' until 'Prog' is flashing. Press 'OK'. 'NEW PROG' will flash
on the display. Press the '◄' or the '►' button until 'CLEAR' flashes on the display. Press 'OK'.
2.
'SINGLE' will flash on the display. Use the '◄' or the '►' button until 'ALL' is flashing on the display. Press 'OK'
and 'CONFIRM' will flash on the display.
3.
Press 'OK' to confirm the clearing of all program settings or press the 'MENU' button to escape and not clear any
program settings.
F. OVERRIDES
1.
To temporarily override a current charge or control cycle, press and release the '◄' and the '►' buttons at the same
time. '
' will appear and the clock will reverse the current program cycle. This override status will remain until
the next program cycle time, or it can be canceled by pressing and releasing the '◄' and the '►' buttons at the same
time again and 'OFF' will display.
2.
The time clock can also be placed in a permanent ON (Charge) or permanent OFF (Control) status. To do so, press
and hold both the '◄' and the '►' buttons until 'PERM ON' ( ) or 'PERM OFF' (
) is displayed.
Follow the same procedure to cancel the override.
G. RESET TIME
NOTE:
The manufacturer recommends NOT using the 'Res' button unless absolutely necessary.
1.
Press the “Res” button to reset time, day, month, and year.
NOTE: This does not reset programmed control and charge cycles.
2.
User manuals / installation manuals. Welcome to the Panasonic manual download centre where you can easily access relevant documentation for our products. Please note that although we do have a number of manuals, not all models are available. Panasonic rx-4940 user manual download.
If the “Res” button is pushed, refer to the “Setting the Time Clock” instructions above for programming.
Page 1 of 2
Theben Tr 610 S Instructions
Document #1200368.doc Rev 4
01/17/07
HAZARDOUS VOLTAGE:
Risk of electric shock. Can
cause injury or death. This
device may be connected to
more than one branch circuit.
Disconnect all branch circuits
WARNING
STEFFES CORPORATION
THEBEN MODEL “TR610 TOP” TIME CLOCK
SETTING INSTRUCTIONS
Item #1301007R (120V Clock) and Item #1301008R (240V Clock)
NOTE: The Theben time clock is equipped with a lithium battery with an
approximate 4year power reserve.
Throughout the programming of the time clock, if there is approximately 90 seconds of
inactivity (no buttons are pushed), the display will automatically reset to normal
operation. If the clock resets and the program information you are entering or editing
is not stored, the time clock will default to the previous settings. The new information
will have to be reprogrammed.
A. SETTING THE TIME CLOCK
1.
The time clock is delivered in a 'sleep' mode. To activate without a service
voltage, press and release one of the four buttons.
2.
Select the national language by pressing the '◄' or '►' button until the desired language is
flashing. Press 'OK' to save the selection.
3.
To set the year, press the '◄' or '►' button until the current year is displayed. Press 'OK' to
save.
4.
Set the month by using the '◄' or '►' button until the current month is displayed. Press
'OK' to select.
5.
Set the day of the month using the '◄' or '►' button until the day of the month is displayed.
This display will show the month selected, followed by the day (09.01). Press 'OK' to select.
6.
Set the current hour of the day using the '◄' or '►' button until the hour is displayed. Make
sure the correct am/pm hour is selected. Press 'OK'.
7.
Set the minutes using the '◄' or '►' button. Press 'OK' to save.
NOTE: At this point, the time clock should continue with setup of daylight savings time; however,
the clock may return to the normal operating mode and skip the daylight savings section. If
this occurs, press the 'MENU' button until the “¹” is flashing at the top of the display.
Press 'OK' and repeat Steps 38.
8.
To set whether or not daylight savings time (DST) will be utilized, press the '►' button until 'SUM/WIN' is
displayed. Press 'OK'.
a. With Daylight Savings Time
¨
Press the '►' button until 'WITH S/W' is displayed. Press 'OK'.
¨
Use the '►' button until 'USA/CAN' is displayed. Press 'OK'.
b. Without Daylight Savings Time
¨
Theben Tr 610 S Manuale Italiano
Press the '►' button until 'NO SU/WI' is displayed. Press 'OK'.
9.
The clock will return to the time/status display and the day of the week should automatically be indicated by an
arrow (1 = Monday..7 = Sunday) at the bottom.
NOTE: If daylight savings time is to be recognized, a snowflake or a sun will appear in the clock
display. A snowflake indicates winter months (days between last Saturday in October and
first Sunday in April). A sun indicates summer months (days between first Saturday in April
and last Sunday in October).
B. SETTING THE CHARGE (ON) AND CONTROL (OFF) CYCLES
NOTE:
Start times for each charge (on) and control (off) cycle MUST be set. They DO NOT need to be set in
sequential order.
1.
Press the “MENU” button until 'Prog' is flashing in the upper portion of the display. Press 'OK'.
2.
Use the '◄' or '►' button until 'NEW PROG' is flashing in the display. Press 'OK'. 'FREE' and a number will
automatically appear after a few seconds to indicate how many program locations are available. There are a total of
28 program locations available if no program settings have been entered.
3.
The clock will automatically display 'TIME ON' or 'TIME OFF' toward the top of the display. Below this, 'On' or 'Off'
will be flashing. Use the '◄' or '►' button until “Time ON” displays and press “OK” to set the charging period.
Reminder: “ON” is a charging cycle and “OFF” is a control cycle.